主机调试英语
广播主机调试:这个是在主机总线盘消防广播按钮直接启动相应楼层广播可以直接呼叫各个楼层的广播,实现消防联动的时候整栋楼的消防广播都回升向紧急疏散的才可以的。
1、打开楼层呼叫器主机,把拨码开关全部拨到ON的反面。
2、同时按住“学习”和“清除”按键,打开电源开关,6秒后松开按键,清除主机内所有数据,系统进入拨码方式。
3、按下“学习”按键6秒,需要学习的楼层显示在“当前呼叫”数码管上,“等待一”上显示St,系统进入学习状态。
性能特点:
显示器采用LED数码管和LED指示灯。用于指示录/放音进度及各种状态。按键采用轻触式按键,进行各功能转换并由指示灯指示当前状态。
内置有一路消防应急广播音源(固化语音)和两路外部辅助输入(线路Ⅰ、线路Ⅱ),可通过面板随意切换。广播音源也可通过外部电平触发信号强制切换至应急广播状态,信号撤消后恢复至切换前状态。
同时广播主机还包含两路单声道输出接口,可以将当前广播音源输出至GB9221消防广播功放机。
配置特制传声器。应急广播状态下可进行现场广播,广播内容会被自动记录以备查询;非应急状态下也可对现场广播,此时录音不会被记录,传声器广播时其他音乐信号会被自动抑制。
调试是指主机负荷试验么?
船浮在水里,冷态+热态测量。数据偏差在+/- 20%理论数据以内合格
使用debug,当然得先输入 debug 回车 才能输入debug命令 debug似乎非常复杂,不清楚还是不要用好
空调主机英语
空调主机与chiller的区别在于空调的主机是制冷用的,chiller是后备储能的。空调室内机,也就是主机,主要部件:蒸发器(翅片铜铝换热器)、风机电机、电控部件、节流部件、外壳。空调室外机,也就是外机,主要部件:压缩机、冷凝器(翅片铜铝换热器)、风机电机、电控部件、节流部件、气液分离器、储液罐、四通换向阀、外壳等等。空调分为单冷空调和冷暖两用空调,工作原理是一样的,空调以前大多一般使用的制冷剂是氟利昂。氟利昂的特性是:由气态变为液态时,释放大量的热量。而由液态转变为气态时,会吸收大量的热量。(即先吸热气化再液化放热)空调就是据此原理而设计的。习惯上称空调的主机是按装在室内的那部分.室外机是按装在室外的那部分。但是事情是恰恰相反,因为空调在制冷时压缩机和冷凝器工作是要产生热量的,反之制热时冷凝器需要吸热,一般情况下室外机是空调的核心。所以室外机应称主机,安装在室内机上有蒸发器(制热时可称为冷凝器)、风扇和感温控制系统。现在通称室内机与室外机。空调是现代生活中人们不可缺少的一部分,空调为人们提供了凉爽,但同时空调常开也易引起疾病,如“空调病”等,需要慎用。空调的主要形式分为:柜机空调,挂机空调,水空调,窗机空调(室内室外各一半),中央空调,一拖二式空调(一个室外机同时控制两个室内机)等形式。
outdoor part of air conditioning
Air host
Air conditioner
调试整机英语
Traffic in people's daily life plays an important role, as people have become increasingly frequent social activities and this is reflected most vividly. The emergence of traffic lights so that traffic can be effective control, for ease traffic flow, increase road capacity and reduce traffic accidents have a demonstrable effect. The system uses microcomputer AT89C51-centric devices to design the traffic control signal controller, the system practical, simple operation, expansion and strong. This design is the adoption of SCM simulation of traffic lights at the crossroads of various status display and countdown time.This design system is composed of MCU I / O port expansion systems, traffic light status display system, LED digital display control systems, emergency interrupt system, reset circuit of several major components. In addition to the traffic light system, the basic functions, but also has a countdown, emergency processing functions to achieve a better simulation of the situation that may arise at a crossroads.Software using 89C51 programming and wrote the main program, LED digital display control program, interrupt program delay procedures. After machine commissioning, implementation of the simulation traffic light intersections.
英文单词,本意是臭虫、缺陷、损坏、犯贫、窃听器、小虫等意思。现在人们将在电脑系统或程序中,隐藏着的一些未被发现的缺陷或问题统称为bug(漏洞)。 由于现在社会的发展,bug另有一种引申意义,用来形容某事物厉害的超乎想象,望采纳
整机工序The whole machine working proceduremachine work [机] 机械加工;切削加工短语machine-working taps 攻丝机machine tool working lamp 机床工作灯machine for working soil 土壤耕作机It runs automatically in rotating piston pump, delivering, filling and sealing cap. Thewhole processes are finished by the single machine, which can save the area and make it high automatically.整机能自动进瓶、跟踪灌装、自动送盖上盖和旋盖或螺纹轧盖、封口,全部工序一机完成,可节省占地面积,自动化程度高。
没一种产品都有一套完整的性能指标要求,但并不说这个产品一生产出来它就可以达到全部的这些指标,因此就需要整机调试,也叫统调,即将各项指标调试到允许的范围之内。
调试机械英语
machine /machinery /engine 都可以
调试的英文:shakedown test
test 读法 英 [test] 美 [test]
1、 考验;试验;测试
2、作不及物动词的意思是:试验;测试;接受测验
短语
1、hardness test [力] 硬度试验 ; 硬度测试 ; 硬度实验
2、Dynamic test [试验] 动态试验 ; [试验] 动态测试 ; [力] 动力试验 ; 动力测试
3、orthogonal test [农学] 正交试验 ; 正交实验法 ; 正交设计
4、Term test 项测试 ; 长期试验 ; 期中考试
5、Tourniquet test 束臂试验 ; 血压带试验 ; 止血带试验
test的词语用法
1、test用作名词的基本意思是“测验”,指用一系列需要回答的问题来考查应试者对某一科目的了解,也可指用一系列动作来证明某人做得如何,还可指“体检,化验”“试验,检验”,引申可作“考验”解,是可数名词。
2、test也可表示用于检验其他事物标准的“判断准绳,试金石”。
3、test用作动词的基本意思是“测验”“检验”“检查”“考查”,指按标准对受试之物进行测试,目的在于检验某物的内容或可能存在的缺点、毛病等,引申可作“考验”“勘探,探测”解。
4、test一般用作及物动词,接名词或代词作宾语,可用于被动结构。
5、test可以是名词,可以是动词,作为名词时前面要加冠词the或a,如put to the test(试验)。
机械:Mechanical名词:1.mechanical2.machinery3.machine4.mechanism形容词:mechanic
机械设备调试,定期的调试吧。定期调试 periodic calibration调试 n. calibration / calibration and testing调试 v, calibrate and testcalibrate v.tr. cal.i.brat.ed; cal.i.brat.ing; cal.i.brates;To check, adjust, or determine by comparison with a standard (the graduations of a quantitative measuring instrument): 校准校核、调整或通过与一标准比较而确定(量化仪表上的标度):calibrate a thermometer.校准一支温度计To determine the caliber of (a tube).确定(管道的)口径To make corrections in; adjust: 使标准化对…作校正;调整:calibrated the polling procedures to ensure objectivity.为保证客观性而使投票过程标准化
单机调试英语
5.2.7 over-excitation limitation function: ( excitation current and stator current limit)Excitation limiting function ( excitation current and stator current limiting )According to the PQ generator characteristic curve to check its limit the generator at a power output under reactive load. In P = 50% cases according to the stator current value setting the parameters of generator excitation current limiter action and recording terminal voltage of generator excitation current excitation voltage active and reactive power signal according to the system response appropriate adjustment of PID parameters in limiter action on the regulator stability is good.5.2.8 strong excitation limit function:Inverse time starting current is 1.1 times the load rated excitation current, and according to the generator thermal curve to determine the inverse time characteristic.5.2.9 volts Hertz limit:To avoid generating set and the excitation transformer iron core through magnetic flux saturation, regulator equipped with V / Hz limiter and characteristic curve, if the generator voltage is above a certain frequency lower limit value, will automatically reduce the given value of the generator voltage requirements with characteristic curve. According to setting limit check its protective action should be correctly. During no-load operation situation drop generator speed verify V / Hz limiter work normal.5.2.10 pulse examination:( static test ) check rectifier screen six phase pulse amplitude and phase of the correctness. Recording trigger circuit of phase shift characteristic.5.2.11 PT breaking and missing pulse switching testRegulator in the A channel operation, disconnect any one phase voltage or analog pulse loss, regulator should switch to B channel operation.5.2.12 low-excitation limited testP / Q low excitation limit test, low-excitation side stator current limit, minimum excitation current limit.Set P / Q low excitation limit parameter, in P = 0%, 25%, 50%, 75%, 100% in the case of the generator excitation system to reduce the low excitation limiter action, recording limiter action current operation value, by doing step load limiter action after the performance validation.In the generator with different load cases, artificial regulation of excitation, the leading phase operation of generator under excitation limiter limits, till action. And record the low-excitation limited movement of the active power and reactive power. Do 3-5, depict the low-excitation limited line.In the active P = 0%, 25%, 50%, 75%, 100% in the case of the generator phase advance operation verification of low excitation limit in a pre-set limit line can correct action and in the limit point of doing step response. Usually step volume < 3% to test low excitation limiter action stability according to the response system to adjust PID parameters in the test process of recorded wave voltage excitation current excitation electric pressure of active and reactive power signal and record limit action corresponding to the excitation current value. According to the automatic running mode under low excitation limit action recorded when the corresponding excitation current value set manual operation mode under low excitation limit line parameters.5.2.13 inverter de-excitation testThe generator no-load rated operation, manual inverse de-excitation and trip fmk, recording demagnetization process of excitation voltage, excitation current, voltage and other data. Simultaneous measurement of de-excitation time. Exit command was inactivated by excitation magnetic recording terminal voltage excitation voltage excitation current signal validation de-excitation process.The 5.2.14 regulator load rejection test ( left active and casting reactive power test )A left active: generator with 50% and rated 100% load operation, suddenly jump development motor switch, the rejection to the load, record generator excitation voltage, excitation current, voltage, waveform, recorded before and after load rejection n numerical stability.B. Casting reactive power: usually with appropriate active P = 15% in var Q = 10% 25% 50% 75% 100% five point on the load rejection test and recording terminal voltage of generator excitation current and reactive power signal in the test process according to the response system is adjusted in response to the control parameters to swing load voltage overshoot in line with gb. ( special test be arranged )5.2.15 rectifier cabinet on-line measurement of flow inspection5.2.16 rotor grounding protectionThe person with the standard of grounding resistance box in the rotor circuit with resistor, the circuit to the alarm value causes the alarm protection, to reduce grounding resistance action trip exports de-excitation switch.5.2.17 PT breaking testIn the case of no-load operation pull PT wiring verification switch control logic of normal and recording terminal voltage excitation voltage excitation current signal.The 5.2.18 after completion of the test: careful proofreading two channel parameter setting confirmation parameters back to FLASH MEMORY remove the debugging tools for the debugging process of removal of the panel screws and connecting the recovery and clean-up site on the control panel will control the cutting away into the distance. In one test, the accident memory unit.
1、电气仪表的基本原理。2、PLC模块信号的基本原理。3、PLC本身的工作原理。4、PLC的编程语言。
echo详细用法>>英 ['ekəʊ] 美 ['ɛko] vi.发出回声;回响vt.重复;模仿;附和n.回声;重复;共鸣Echo.n.[希神]山林女神(失恋于那喀索斯;其哀声留于山间成为回声)[例句]That's `neat' – November Echo Alpha Tango.那是neat,即November Echo Alpha Tango。[其他]复数:echoes第三人称单数现在时:echoes现在分词:echoing过去分词:echoed过去时:echoed
英文名echo,来源于希腊神话中的Echo女神。希腊神话中,宙斯的老婆赫拉嫉妒山林女神Echo的美貌,让她失去了正常的说话能力,只能重复别人的话的最后三个字。这也就是Echo后来成为“回声”的由来